Start with a finish that works for every look
Glittery Emerald is a shimmery deep green soak-off gel that mixes blue and emerald tones with sparkles. That combination gives you a jewel-toned base that shifts under light, so it can carry a simple accent nail or a full festive set.
The formula calls for 2-3 coats for a flawless finish, and darker colors like this one require longer curing than lighter shades. Cure 2 minutes under a UV lamp or 30 seconds under an LED lamp, and cure between every thin layer.
Prep matters as much as the color. Remove and push back cuticles, buff the nail plate to remove shine, and clean with alcohol to remove oils and dust. Avoid lotion or cuticle oil before application, since either can cause premature lifting. Keep gel off your skin and cuticle area.
Glittery Emerald at a glance
- Glittery Emerald: 15 ml | 0.5 fl oz bottle of shimmery deep green soak-off gel polish. A single bottle gives you enough for multiple festive manicures and touch-ups.

Glittery Emerald - Glittery Emerald: Apply 2-3 thin coats, curing between each layer (2 minutes UV, 30 seconds LED). Thin layers cure evenly and help the glitter sit smoothly instead of clumping.
- Glittery Emerald: Use with Soak Off Base Coat and Soak Off Top Coat Gel from the same line. Matching base and top coats are recommended for the strongest, most reliable finish.
Five festive looks you can build with Glittery Emerald
- 1. Full glitter emerald manicure: Apply base coat and cure. Then apply 2-3 thin coats of Glittery Emerald, curing between each. Finish with top coat and cure 30-60 seconds under UV/LED. Cap the free edge for a protective seal.
- 2. Emerald accent nail: Paint all nails with a neutral or clear gel, and use Glittery Emerald on the ring finger or thumb. Cure each layer as directed. This keeps the sparkle focused and stretches the bottle further.
- 3. Glitter gradient tips: Start with a sheer base color and cure. Then apply Glittery Emerald only to the tips, using a thin coat and curing. Add a second coat closer to the tip for a gradient effect. Top coat and cure.
- 4. Emerald French twist: After a base color and cure, paint a thin line of Glittery Emerald along the smile line. Cure, then seal with top coat. Use a small brush for control, and keep gel off the skin.
- 5. Glitter ombre fade: Apply Glittery Emerald to the lower half of the nail and cure. Then use a sponge or brush to fade a second coat upward, curing between layers. Finish with top coat for a seamless sparkle fade.
Cure times and application tips that protect the finish
Glittery Emerald needs to be cured under a UV/LED lamp. The supplied instructions list 2 minutes for UV and 30 seconds for LED, with 30-60 seconds between layers for base and top coat. Because darker colors require longer curing, give each coat the full time rather than pulling the hand out early.
Apply thin coats and cure between each layer. A thick coat can trap uncured gel and cause lifting or uneven texture. Use base and top coat from the same line, and cap the free nail edge to create a protective seal around the tip and sides.
After your manicure, apply daily cuticle oil and avoid soaking in hot water for the first few hours. To remove, soak in acetone or use a gel polish remover.
What the supplied information does not confirm
- Glittery Emerald: The record lists a professional 3-step system but does not specify whether a separate primer or bonder is required. If your routine includes a primer, follow its own instructions; the Glittery Emerald record does not confirm one way or the other.
- Glittery Emerald: The ingredient list may vary slightly by lot number; refer to the label on your bottle. Check your own bottle for the most accurate ingredient information, especially if you have sensitivities.

